ไทย
Eng
จอคอม "HyperPixel 4.0 High-Resolution Display for Raspberry Pi Touch Screen" ตอนนี้ราคาลด 24% จากราคาเดิม 2900.00 บาท ลดเหลือ 2190.00 บาท เท่านั้น สินค้าจัดส่งมาจาก กรุงเทพมหานคร ยี่ห้อ Pimoroni และขายโดยร้าน Terminus Thailand
A high
-resolution, high
-speed
4.0" TFT display for your Raspberry Pi with optional capacitive multi
-touch!
HyperPixel
4.0 is the perfect way to use your Pi without a bunch of cables or a bulky display. Design your own interface to control your project, display data, or turn your Pi into a tiny media centre.
This new version of HyperPixel has a gorgeous IPS display, with wide viewing angles, custom
-made cover glass (on the touch version), and the alternate I2C interface is broken out for advanced users.
It's available in touch and non
-touch versions, depending on your preference.
Features
High
-speed DPI interface
4.0" IPS (wide viewing angle, 160°) display (
86.4x
51.8mm)
800x480 pixels (~235 PPI)
18
-bit colour (262,144 colours)
60 FPS frame rate
Capacitive touch*
40
-pin female header included to boost height for Pi B+, 2, 3, 3B+ and 4
Standoffs included to securely attach to your Pi
Compatible with all 40
-pin header Raspberry Pi models
One
-line installer
*Only on Touch version
HyperPixel uses a high
-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays use. It has a 60 FPS frame rate and a resolution of approximately 235 pixels per inch (800x480) on its
4.0" display. The display can show 18
-bits of colour (262,144 colours).
The Touch version has a capacitive touch display that's more sensitive and responsive to touch than a resistive touch display, and it's capable of multi
-touch!
Everything comes fully
-assembled, and there's no soldering required! The display is securely stuck down to the HyperPixel
4.0 PCB and connected via a neat little flush
-mounting FPC cable. Just pop HyperPixel
4.0 on your Pi and run our installer to get everything set up!
We've put together a one
-line
-installer to configure your Pi properly for HyperPixel
4.0 and to enable the touch screen on the touch version. Note that you'll need another display, keyboard, and mouse to install the software, or you could do it remotely over SSH if you follow our guide on how to set your Pi up headlessly.
-resolution, high
-speed
4.0" TFT display for your Raspberry Pi with optional capacitive multi
-touch!
HyperPixel
4.0 is the perfect way to use your Pi without a bunch of cables or a bulky display. Design your own interface to control your project, display data, or turn your Pi into a tiny media centre.
This new version of HyperPixel has a gorgeous IPS display, with wide viewing angles, custom
-made cover glass (on the touch version), and the alternate I2C interface is broken out for advanced users.
It's available in touch and non
-touch versions, depending on your preference.
Features
High
-speed DPI interface
4.0" IPS (wide viewing angle, 160°) display (
86.4x
51.8mm)
800x480 pixels (~235 PPI)
18
-bit colour (262,144 colours)
60 FPS frame rate
Capacitive touch*
40
-pin female header included to boost height for Pi B+, 2, 3, 3B+ and 4
Standoffs included to securely attach to your Pi
Compatible with all 40
-pin header Raspberry Pi models
One
-line installer
*Only on Touch version
HyperPixel uses a high
-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays use. It has a 60 FPS frame rate and a resolution of approximately 235 pixels per inch (800x480) on its
4.0" display. The display can show 18
-bits of colour (262,144 colours).
The Touch version has a capacitive touch display that's more sensitive and responsive to touch than a resistive touch display, and it's capable of multi
-touch!
Everything comes fully
-assembled, and there's no soldering required! The display is securely stuck down to the HyperPixel
4.0 PCB and connected via a neat little flush
-mounting FPC cable. Just pop HyperPixel
4.0 on your Pi and run our installer to get everything set up!
We've put together a one
-line
-installer to configure your Pi properly for HyperPixel
4.0 and to enable the touch screen on the touch version. Note that you'll need another display, keyboard, and mouse to install the software, or you could do it remotely over SSH if you follow our guide on how to set your Pi up headlessly.
| Contrast ratio: | 500 |
| Please note: | when installing HyperPixel 4.0 onto your Pi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header). Also take care not to pull on the edges of the glass display when removing your HyperPixel. |
| Open a terminal, and type curl https: | //get.pimoroni.com/hyperpixel4 | bash to run the one-line installer and set your HyperPixel 4.0 up. |
| Find the GitHub repository here: | https |
ข้อมูลเฉพาะ จอคอม
- แบรนด์ Pimoroni
- SKU 1680424317_TH
- ร้านค้า Terminus Thailand
หากรายละเอียดยังไม่เพียงพอ โปรดดูรายละเอียดเพิ่มเติมได้ที่ร้านด้านล่าง....
Terminus Thailandมี Hyperpixel 4.0 High-Resolution Display For Raspberry Pi Touch Screen ให้เลือกจำนวนมาก นานัปการแนว แบ่งเป็น Hyperpixel 4.0 High-Resolution Display For Raspberry Pi Touch Screen สำหรับคุณสุภาพบุรุษ และก็ Hyperpixel 4.0 High-Resolution Display For Raspberry Pi Touch Screen สำหรับคุณสุภาพสตรี อย่างแจ่มแจ้ง ทำให้ง่ายและก็สบายอย่างมากในการเลือกช้อปปิ้ง พวกเรา
Add a review